山東通風管道加工運行時，由部分新風與部分室內回風混合后的空氣，在室內機組中經過凈化、濕調、冷卻或加熱處理后，通過送風管送各個房間中，再由回風管將室內空氣集中送回室內機組。整個系統的運行由一個溫控器來自動控制設備的啟停和保持室內恒溫。

　　The processing operation of Shandong ventilation duct, in part by the fresh air and return air mixing part of indoor air after, after cleaning, conditioning, cooling or heating treatment in the indoor unit, the air supply pipe to send to each room, the indoor air concentration to indoor units from the air return pipe. The whole system is operated by a thermostat to automatically control the start and stop of the equipment and maintain the indoor constant temperature.

　　新風從空氣較潔凈區域進入，由污濁處排出。一般污濁空氣從浴室、衛生間及廚房排出，而新鮮空氣則從起居室、臥室等區域送入。

　　Fresh air enters from the clean air area and is expelled from the polluted area. General dirty air from the bathroom, bathroom and kitchen, while the fresh air from the living room, bedroom and other areas into.

　　通風管道加工要注意細節方面，只有注重細節才能確保風管在使用中不出現問題。

　　Attention should be paid to the details of ventilation duct processing. Only by paying attention to detail can the air duct be free from any problems during use.

　　1.清潔板材切割面的粉末、油漬、水漬、灰塵,用毛刷在切割面上涂刷膠粘劑.

　　1. clean the cutting surface, powder, grease, water stain and dust, and brush the adhesive on the cutting surface

　　2.板材接縫處從一端另一端按對中位置粘上壓敏鋁箔膠帶,壓敏膠帶粘在一邊的寬度不小于20mm.

　　2. the plate joint from one end to the other end, press the middle position of the pressure sensitive aluminum foil tape, the pressure sensitive adhesive tape on the side of the width of not less than 20mm.

　　3.將風管面板按設計要求粘合,待涂膠不粘手時.并用刮板壓平.對難以刮平的局部,可用木錘輕輕錘平.

　　3., the wind tube panel according to the design requirements of bonding, to glue do not stick hand. And use scraper leveling. For difficult to flat parts, can use wood hammer gently hammer flat

　　4.清潔板材切割面的粉末,按空調風管加工任務單檢查風管面板是否符合設計要求.

　　4. cleaning panel cutting powder, according to the air conditioning duct processing task list, check whether the wind pipe panel meets the design requirements

　　5.檢查板材接縫粘接是否達到質量規.

　　5. check whether the bonding of plates meets the quality requirements

　　空調通風管道可采用地板送風或天花板送風，除了可調節溫度，還可通過將增濕器和溫度調節器一起工作來調節空氣濕度。其還具備自動新風系統，可把室外的新鮮空氣以每小時6次的頻率為室內進行一次更換。

　　The central air conditioning ventilation pipe can be underfloor or ceiling fan, in addition to adjust the temperature, but also through the humidifier and the temperature regulator working together to regulate the air humidity. It also has automatic fresh air system, outdoor fresh air can be replaced at 6 times per hour for indoor replacement.

　　本文由山東通風管道加工為您提供，我們的網站是:http://m.17hhw.com/我們將以全心全意的熱情為您提供更的服務，歡迎您的訪問!

　　This article is provided by the Shandong ventilation pipe processing, our website is: http://m.17hhw.com/ We will wholeheartedly provide you with better service, you are welcome to visit!

上一篇：玻璃鋼排煙罩的環向強度分配
下一篇：裝置通風管道跨接線的注意事項